https://scholars.lib.ntu.edu.tw/handle/123456789/77000
DC 欄位 | 值 | 語言 |
---|---|---|
dc.contributor | 楊萬發 | en |
dc.contributor | 臺灣大學:環境工程學研究所 | zh_TW |
dc.contributor.author | 詹豐隆 | zh |
dc.contributor.author | Chan, Feng-Lung | en |
dc.creator | 詹豐隆 | zh |
dc.creator | Chan, Feng-Lung | en |
dc.date | 2004 | en |
dc.date.accessioned | 2007-11-29T03:10:21Z | - |
dc.date.accessioned | 2018-06-28T23:22:39Z | - |
dc.date.available | 2007-11-29T03:10:21Z | - |
dc.date.available | 2018-06-28T23:22:39Z | - |
dc.date.issued | 2004 | - |
dc.identifier | zh-TW | en |
dc.identifier.uri | http://ntur.lib.ntu.edu.tw//handle/246246/62811 | - |
dc.description.abstract | 近年來,流體化床結晶技術已經廣泛的應用於含陰離子及陽離子廢水上,除了改善傳統混凝方式易產生大量污泥的缺點,同時生成的晶體可以回收再利用,使重金屬污染物資源化而不會有污泥的二次污染問題,並減少釵h處理的程序,在經濟上的效益更高,能讓處理的廢水降低至排放標準,而不需額外的處理設備。本研究以由三段反應槽串聯而成的流體化床設備來處理含鎳廢水,利用碳酸鈉作為結晶藥劑,使鎳離子形成碳酸鎳或氫氧化鎳的難溶性物質覆誚b擔體的表面。藉由改變不同的反應莫耳比、水力負荷、擔體量、廢水負荷等參數來進行試驗,以找出最佳的操作條件,此外,並以連續操作的方式對廢水進行處理,探討不同反應槽的擔體表面結晶結構及分析其中的結晶含量。 實驗結果顯示:在不同水力負荷與反應莫耳比操作下,越慢的水力負荷有越高的去除效果,以23 ~30 m/h為最適合,當總碳酸鹽與鎳離子之反應莫耳比達2.5時有最好的處理效率,總碳酸的量過低則系統的飽和度不足,不僅第一反應槽去除能力不佳,對於過濾後的出流水水質亦無法符合標準,而過高的加藥量則會造成過飽和度太高,雖然出流水過濾後皆能符合排放標準,但對初段反應槽來說則會使處理能力減少,且過多的加藥量亦造成浪費。就填充擔體量而言,增加其填充量雖能提高去除效果,但就實際操作上,考慮到擔體流體化時的膨脹程度,填充的量仍應以反應槽的1/4~1/3高度的擔體量為佳。 就整體的處理能力來說,在較佳的操作條件下,當進入反應槽的鎳離子負荷為3.61 kg/m2h時,第一段反應槽之去除率約90%,而處理後的出流水鎳離子濃度則可控制在2 mg/l以下;而當進流鎳離子負荷小於1.87 kg/m2h時,則排放水鎳離子濃度可控制在1 mg/l以下。當採迴流方式時,過低的反應莫耳比將造成放流水水質隨時間的增加而變差,過高的莫耳比亦有同樣的結果,最適的莫耳比為2左右。 在連續操作方面,當進流的鎳離子濃度為35 mg/l時,處理能力並不會因操作時間長而降低處理能力,處理過程中所考慮的只是因擔體的增大致使操作時間增長,反應槽的自由空間也相對減少而需進行更換擔體,就反應後的擔體結晶進行表面的結構觀察發現,確實有綠色結晶物覆誚b擔體上,而經由SEM影像圖來看,其結構的緻密性則以第一段反應槽為最佳,顯示末段反應槽的沈澱比例較高。 | zh_TW |
dc.description.abstract | In recent years, fluidized bed pellet reactors have been extensively applied in the removal of anions and cations from wastewater. It improved the disadvantage of producing a large number of sludge easily in traditional unseeded precipitation treatment, and produced reusable pellets as resources. This technology cut down many processors and let the contaminants of heavy metals resource, but no second pollution problems of sludge. On the processor of wastewater, it could fit the emission standard of wastewater easily, and it had even more economical benefit and had no additional treatment equipment. In this research, the crystallization process of a fluidized bed pellet reactor was studied in the treatment of nickel-containing wastewater .The crystallization reactor was connected by three same reactors. Sodium carbonate was added as the reagent solution to form nickel carbonate and nickel hydroxide on the surface of the pellets in fluidized bed reactor. This study investigated the effects of some important factors, including CT/Ni feeding ratio、upflow rate、quantity of pellet、Ni-loading etc. We made experiment by continuous worked for conferring the crystals structure of pellet’s surface in different reactors, and analyzed the coated quantity under optimum operation conditions finally. The results showed that operated with the different upflow rate and different CT/Ni feeding ratio ,the lower upflow rate increased removal efficiency ,especially on the condition of 23~30 m/h and CT/Ni feeding ratio was 2.5. The processor system would in low supersaturation when CT is not enough .On this condition the first reactor had bad removal efficiency and emission still couldn’t fit to the emission standard of wastewater. In the same way, overdosed of sodium carbonate would lead to high degree of supersaturation, the way would decrease removal efficiency of first reactor, but the filtrated wastewater could fit the emission standard .For the quantity of pellet, the increasing quantity could improve the removal efficiency. But in practical operation, we considered the expand level of pellet when it fluidized, the better amount of pellets should be 1/3~1/4 times of reactor’s height. For macrocosm treatment ability (under optimum operation conditions), the removal efficiency of the first reactor was about 90% when inflow Ni-loading was 3.61 kg/m2h.The concentration of nickel was less than 1 mg/l and could fit the emission standard as Ni-loading was smaller than 1.87 kg/m2h.On the condition of recirculation, the removal efficiency was more and more terrible with operation time increased as the too low or high CT/Ni feeding ratio. The optimum CT/Ni feeding ratio was 2. In the continuous process, we used as 35 mg/l of nickel inflowing in the fluidized bed, the results show that the removal efficiency would not decrease as operation time increased. The important factor was that the pellet’s size would more and larger and the interior’s free space of reactor decreased. We must change the pellet in fluidized bed reactors during a series processor. By the way, we observed the variation of pellet’s surface during the processor and discovered that some green crystal coated on pellet’s surface certainty. And then photographed the pellet’s surface by SEM, the images showed that the preceding reactor had the better strict structure. This result also showed that the majority mechanism of crystallization occurred in preceding reactor and sediment occurred in later reactor. | en |
dc.description.tableofcontents | 第一章 前言 ……………………………………………………………1 1-1 研究緣起 ………………………………………………………1 1-2 研究目的與內容 ………………………………………………3 第二章 文獻回顧 ………………………………………………………4 2-1 重金屬廢水來源及特性 ………………………………………4 2-2 過飽和度與平衡濃度 …………………………………………6 2-2-1 可溶物系與微溶物系之過飽和度定義…………………7 2-2-2 過飽和溶液之介穩區……………………………………8 2-2-3 化學平衡 ………………………………………………11 2-3 晶體之成核現象………………………………………………13 2-3-1 結晶與沉澱 ……………………………………………13 2-3-2 成核現象 ………………………………………………15 2-3-3 晶體成長理論 …………………………………………17 2-4 流體化床原理與特性…………………………………………20 2-4-1 流體化床 ………………………………………………20 2-4-2 流體化床之型式 ………………………………………21 2-4-3 流體化床系統之設計 …………………………………23 2-4-4 流體化床結晶技術(FBC)與傳統處理法之差異………25 2-5 流體化床結晶技術之發展與實廠應用………………………27 2-5-1 流體化床結晶技術之發展 ……………………………27 2-5-2 流體化床結晶技術之實場應用 ………………………28 2-5-3 流體化床結晶技術之相關研究 ………………………30 第三章 實驗設備、材料與方法………………………………………34 3-1 研究架構及實驗流程…………………………………………34 3-2 實驗裝置………………………………………………………34 3-3 實驗設備與材料………………………………………………37 3-4 實驗步驟………………………………………………………38 第四章 結果與討論……………………………………………………41 4-1 不同反應莫耳比與水力負荷對鎳離子結晶去除效果………41 4-1-1 第一反應槽之總鎳離子去除效果 ……………………41 4-1-2 第二反應槽之總鎳離子去除效果 ……………………43 4-1-3 第三反應槽之鎳離子去除效果 ………………………45 4-2 不同水力負荷與擔體量對鎳離子結晶去除效果……………47 4-3 銅、鎳混合廢水之去除效果…………………………………52 4-4 高濃度進流之去除效果………………………………………55 4-4-1 不同pH值之比較………………………………………55 4-4-2 不同加藥比之比較 ……………………………………56 4-5 不同之鎳離子進流負荷………………………………………59 4-6 迴流操作之去除率比較………………………………………60 4-7 連續操作下之去除效果比較…………………………………65 4-7-1 連續72小時(I) ………………………………………65 4-7-2 連續72小時(II)………………………………………66 4-7-3 高濃度連續24小時操作………………………………68 4-8 晶體SEM表面觀察及結晶量分析……………………………69 4-8-1 晶體SEM表面觀察 ……………………………………69 4-8-2 擔體結晶量分析 ………………………………………77 第五章 結論與建議……………………………………………………80 5-1 結論……………………………………………………………80 5-2 建議……………………………………………………………82 參考文獻 ………………………………………………………………83 | zh_TW |
dc.format.extent | 1913829 bytes | - |
dc.format.mimetype | application/pdf | - |
dc.language | zh-TW | en |
dc.language.iso | en_US | - |
dc.subject | 流體化床反應槽 | en |
dc.subject | 結晶 | en |
dc.subject | 含鎳廢水 | en |
dc.subject | 擔體 | en |
dc.subject | 連續操作 | en |
dc.subject | crystallization | en |
dc.subject | fluidized bed reactor | en |
dc.subject | nickel-containing wastewater | en |
dc.subject | media | en |
dc.subject | continuous operation | en |
dc.title | 含鎳廢水流體化床結晶處理技術之應用 | zh |
dc.title | The Application of Using Fluidized-Bed Crystallization to Treat Nickel-containing Wastewater | en |
dc.type | thesis | en |
dc.identifier.uri.fulltext | http://ntur.lib.ntu.edu.tw/bitstream/246246/62811/1/ntu-93-R90541112-1.pdf | - |
dc.relation.reference | Adnan A., Mavinic D. S., and Koch F. A. (2003), "Pilot-scale study of phosphorus recovery through struvite crystallization-examining the process feasibility ", J. of Env. Eng. Sci., 2, pp.315-324 Adnan Ali, Koch Frederic A., and Mavinic Donald S. (2003), "Pilot-scale study of phosphorus recovery through struvite crystallization-II:Applying in-reactor supersaturation ratio as a process control parameter ", J. of Env. Eng. Sci., 2, pp.473-483 Ajmal, Mohammad; Rao, Rifaqat A.K.; Ahmad, Rais; Ahmad, Jameel; Rao, Liaqat A.K. (2001) "Removal and recovery of heavy metals from electroplating wastewater by using Kyanite as an adsorbent ", J. of Hazardous Materials , Vol 87, Issue: 1-3, pp. 127-137 Alison Lewis, Karen Petersen and Stella Lacour "Copper removal from acid mine drainage using a pellet reactor ", Al-Jibbouri Sattar, Ulrich Joachim (2002), "The growth and dissolution of sodium chloride in a fluidized bed crystallizer ", J. of Crystal Growth, 234, pp.237-246 Charerntanyarak Lertchai (1999), "Heavy metals removal by chemical coagulation and precipitation ", Wat. Sci. Tech., 39, No.10-11, pp.135-138 Eggers E., Dirzwager A. H. and van der Honing H. (1991), "Full-scale experiences with phosphate crystallization in a crystalactor ", Wat. Sci. Tech., 24, pp.333-334. Giulietti M., Seckler M.M., Derenzo S., M.I.Ré and Cekinski E. (2001), " Industrial crystallization and precipitation from solutions:state of the technique ", Braz. J. Chem. Eng. , 18, Graveland A., van Dijk J. C., de Moel P. J., and Oomen H. H. C. M. (1983), "Developments in water softing by means of pellet reactors ", J. AWWA, 75(12), pp.619-625 Guillard D., Lewis A. E. (2001), "Nickel carbonate precipitation in a fluidized-bed reactor ", Ind. Eng. Chem. Res., 40(23), pp.5564-5569 Guillard Damien and Lewis Alison E. (2002), "Optimization of Nickel Hydroxycarbonate Precipitation Using a Laboratory Pellet Reactor ", Ind. Eng. Chem. Res., 41, pp. 3110-3114 Harms W. D. Jr. and Robinson R. B. (1992), "Softening by Fluidized Bed Crystallizers ", J. of Envi. Eng., 118, pp.513-529. Hirasawa Izumi, Kaneko Shogo, Kanai Yuuji, Hosoya Shingo, Okuyama Kumiko, Kamahara Takashi (2002), "Crystallization phenomena of magnesium ammonium phosphate(MAP) in a fluidized-bed-type crystallizer ", J. of Crystal Growth, 237-239, pp.2183-2187 Kind M. and Mermann A. (1990), "On Supersaturation during Mass Crystallization from Solution ", Che. Eng. Tech., 13, No.650, pp.50-62 Montastruc L., Azzaro-Pantel C., Biscans B., Cabassud M. and Domenech S. (2003), "A thermochemical approach for calcium phosphate precipitation modeling in a pellet reactor ", J. of Chem. Eng., 94, pp. 41-50 Nielsen A. E. and Toft J. M. (1984a), "Electrolyte Crystal Growth Kinetics ", J. of Crystal Growth, 67, 278 Nielsen P.B., Christensen T.C., Vendrup, M. (1997), "Continuous Removal of Heavy Metals form FGD Wastewater in a Fluidised Bed without Sludge generation ", Wat. Sci. Tech., 36, No.2-3, pp. 391-397 Piekema Peter and Giesen Andreas, "Phosphate recovery by the crystallization process: experience and developments ", DHV Water BV Scholler M., van Dijk J. C. and Wilms D. (1987a), "Recovery of heavy metals by crystallization ", Metal Finishing , 85, No.11, pp.31-34 Scholler M., van Dijk J. C. and Wilms D. (1991), "Fluidized bed pellet reactor to recover metals or anions ", Metal Finishing , 89, No.11, pp.46-50 Scholler M., van Dijk J. C. and Wilms D. A. (1987), "Recovery of heavy metals by crystallization in the pellet reactor ", Environmental Technology, K. De Waal and W. Van den Brink(Eds). M. Nijhoff Publ., Dordrecht, p294-303. Seckler M. M., Bruinsma O. S. L. and Rosmalen G. M. van (1996), "Calcium Phosphate Precipitation in a Fluidized Bed in Relation to Process conditions: A Black Box Approach ", Wat. Res., 30, No.7, pp.1677-1685. Seckler M. M., Bruinsma O. S. L. and Rosmalen G. M. van (1996), "Phosphate Removal in a Fluidized Bed-I:Identification of Physical Processes ", Wat. Res., Vol.30, No.7, pp.1585-1588. Seckler M. M., Bruinsma O. S. L. and Rosmalen G. M. van (1996), "Phosphate Removal in a Fluidized Bed-II:Processes Optimization ", Wat.Res., 30, No.7, pp.1589-1596. Shiau Lie-Ding and Lu Tsan-Sheng (2001), "Interactive Effects of Particle Mixing and Segregation on thePerformance Characteristics of a Fluidized Bed Crystallizer ", Ind. Eng. Chem. Res., 40, pp. 707-713 Shiau Lie-Ding, Cheng Shueh-Hen, Liu Yung-Chang (1999), "Modelling of a Fluidized-Bed Crystallizer Operated in a Batch Mode ", Chem. Eng. Sci., 54 , pp.865-871. Shimamura K., Tanaka T. and Ishikawa H. (2003), "Development of a high-efficiency phosphorus recovery method using a fluidized-bed crystallized phosphorus removal system ", Wat. Sci. Tech., l48, No.1, pp.163-170 Tai Clifford Y. (1999), "Crystal growth kinetics of two-step growth process in liquid fluidized-bed crystallizers ", J. of Crystal Growth, 206, pp.109-118 Tai Clifford Y., Shih Cheng-Yi (1996), "A new model relating secondary nucleation rate and supersaturation ", J. of Crystal Growth, 160, pp.186-189 Ulrich Joachim, Strege Christine (2002), "Some aspects of the importance of metastable zone width and nucleation in industrial crystallizers ", J. of Crystal Growth, 237-239, pp.2130-2135 van Dijk J. C. and Braakensiek H. (1984), "Phosphate removal by crystallization in a fluidized bed ", Wat. Sci. Tech, 17, pp.133-142. Zhou Ping, Huang Ju-Chang, Alfred W. F. LI. And Wei Shirly (1999), "Heavy Metal Removal From Wastewater in Fluidized Bed Reactor ", Wat. Res., 33 (8), pp.1918-1924. "Phosphate Recovery where do we stand today? ", Scientific Committee on Phosphates Scope Newsletter, number 41, 2001 Regy Sylvia, Mangin Denis, Klein Jean Paul, Lieto Joseph, 2001, "Phosphate recovery by stuvite precipitation in a stirred reactor ", CEEP Francois M. M. Morel, Janet G. Hering (1993), Principles and Applications of Aquatic Chemistry, Wiley Inter. Sci. 鄭福田(1981),流動砂床應用於廢水中重金屬之去除,國立台灣大學土木工程學研究所,博士論文 陳寶祺(1992),微溶物系之沈澱與結晶,國立台灣大學化學工程研究所,博士論文 石政怡(1996),次成核機構和其在結晶程序上之應用,國立台灣大學化學工程研究所,博士論文 李茂松(1993),流體化床結晶技術在無機廢水處理上之應用性研究,中原大學化學學系,碩士論文 陳政澤(1995),流體化床結晶反應槽回收廢水中中金屬鎘之研究,中央大學環境工程學研究所,碩士論文 洪再生(1996),流體化床結晶技術回收廢水中重金屬銅之探討,中央大學環境工程學研究所,碩士論文 李茂松、廖啟鐘、邵信、游惠宋、黃昆田、吳聯芳、葉啟順,1996年9月,流體化床結晶法應用於冷卻水塔節水之研究,第二屆水再生及再利用研討會 李明政(1998),流體化床結晶技術應用於養豬廢水之研究,台灣大學環境工程學研究所,碩士論文 蔡月珠(2000),流體化床結晶技術在含鎳廢水處理的應用,長庚大學化學工程研究所,碩士論文 游雅芸(2001),流體化床結晶技術在含銅廢水處理的應用,長庚大學化學工程研究所,碩士論文 張曉菁(2001),流體化床結晶技術在含鎘廢水處理的應用,長庚大學化學工程研究所,碩士論文 簡肇成(2001),結合流體化床結晶床與薄膜去除水中硬度之研究,淡江大學水資源及環境工程學系,碩士論文 簡豪挺(2002),污泥重金屬結合型態對化學萃取重金屬效率之影響,成功大學環境工程研究所,碩士論文 李茂松、黃志彬、顏士閔、張王冠,含砷廢水流體化床結晶處理技術之評估,2003產業環保工程實務技術研討會 環工化學,三民書局,民86 電鍍業資源化應用技術手冊,經濟部工業局編印,2002 環境與安全衛生技術發展中心(http://www.e-environment.com.tw/) 綠色環保新技術探討--廢水流體化床結晶處理技術,ITIS專欄 | zh_TW |
item.openairecristype | http://purl.org/coar/resource_type/c_46ec | - |
item.openairetype | thesis | - |
item.languageiso639-1 | en_US | - |
item.grantfulltext | open | - |
item.cerifentitytype | Publications | - |
item.fulltext | with fulltext | - |
顯示於: | 環境工程學研究所 |
檔案 | 描述 | 大小 | 格式 | |
---|---|---|---|---|
ntu-93-R90541112-1.pdf | 23.53 kB | Adobe PDF | 檢視/開啟 |
在 IR 系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。