https://scholars.lib.ntu.edu.tw/handle/123456789/74237
標題: | Processing character of MgO-partially stabilized zirconia (PSZ) in size grading prepared by injection molding | 作者: | Wei, Wen-Cheng J. Lin, Yuh-Pring |
公開日期: | 1998 | 卷: | 18 | 期: | 14 | 起(迄)頁: | 2107-2116 | 來源出版物: | Journal of the European Ceramic Society | 摘要: | The effects of the mixture of coarse/fine ZrO2 powders in various ratios on the properties of injection-molding feedstocks, the degree of debinding, dimension reproducibility, sintering and phase formation of the Mg-partially stabilized zirconia (PSZ) were studied. The feedstocks and injection molded pieces with 3·5 wt% MgO were tested by capillary rheometry, thermal analysis (DSC), and the injection-molded pieces were analyzed by mercury porosimetry, Archimedes' method. After sintered, the density and m-phase were analyzed by SEM and quantitative XRD techniques. Experimental results show when the feedstocks contained ≥50 vol% of coarse powder, the viscosity is lower and the activation energies of the feedstocks are in the same range as that of pure binder admixture. The flowing properties are controlled by the ratio of fine to coarse as the concentration of fine powder was over 50 vol%. In addition, the formulations with a higher content in fine powder would enhance the de-polymerization of PP, improve the dimensional reproducibility, homogeneity, and degree of debinding. With the appropriate controls on the ratio of fine to coarse powders, Mg-PSZ with 60 to 93% theoretical density and uniform microstructure can be produced.The effects of the mixture of coarse/fine ZrO2 powders in various ratios on the properties of injection-molding feedstocks, the degree of debinding, dimension reproducibility, sintering and phase formation of the Mg-partially stabilized zirconia (PSZ) were studied. The feedstocks and injection molded pieces with 3.5 wt% MgO were tested by capillary rheometry, thermal analysis (DSC), and the injection-molded pieces were analyzed by mercury porosimetry, Archimedes' method. After sintered, the density and m-phase were analyzed by SEM and quantitative XRD techniques. Experimental results show when the feedstocks contained ≥50 vol% of coarse powder, the viscosity is lower and the activation energies of the feedstocks are in the same range as that of pure binder admixture. The flowing properties are controlled by the ratio of fine to coarse as the concentration of fine powder was over 50 vol%. In addition, the formulations with a higher content in fine powder would enhance the de-polymerization of PP, improve the dimensional reproducibility, homogeneity, and degree of debinding. With the appropriate controls on the ratio of fine to coarse powders, Mg-PSZ with 60 to 93% theoretical density and uniform microstructure can be produced. |
URI: | http://ntur.lib.ntu.edu.tw//handle/246246/95352 https://www.scopus.com/inward/record.uri?eid=2-s2.0-0032453703&doi=10.1016%2fS0955-2219%2898%2900091-0&partnerID=40&md5=bdb8616b01b71c077bfca3d5efec62c3 |
ISSN: | 09552219 | SDG/關鍵字: | Differential scanning calorimetry; Injection molding; Magnesia; Microstructure; Powders; Rheometers; Scanning electron microscopy; X ray diffraction analysis; Zirconia; Partially stabilized zirconia; Size grading; Ceramic materials; zirconium oxide |
顯示於: | 材料科學與工程學系 |
在 IR 系統中的文件,除了特別指名其著作權條款之外,均受到著作權保護,並且保留所有的權利。